APISQUEEN W300 Waterproof Remote Controller: Complete Setup, Operation and User Guide

The APISQUEEN W300 is a 2.4GHz wireless remote control system designed for boats, underwater thrusters, marine vehicles, and other remote-controlled propulsion applications.

Featuring a 5-channel receiver, built-in gyroscope, dual-motor control, and cruise control functionality, the W300 provides more than basic wireless throttle operation. It also supports automatic heading correction for compatible dual-thruster systems and an optional GPS electronic anchor function.

Whether you are installing the W300 for the first time or learning how to use its advanced features, this guide covers everything you need to know, including receiver installation, factory pairing, throttle calibration, cruise control, heading correction, charging, and troubleshooting.

1. APISQUEEN W300 Remote Controller Overview

The W300 system consists of a handheld wireless remote controller and a separate receiver.

The handheld controller provides wireless operation, while the receiver processes control signals and communicates with connected motor controllers (ESCs).

Remote Controller Buttons and Indicators

The main controls include:

  • Motor 1 / Motor 2 Joystick: Controls the corresponding motor channels.

  • Acceleration Button: Increases the cruise control speed.

  • Deceleration Button: Decreases the cruise control speed.

  • OK Button: Used for confirmation and the optional electronic anchor function.

  • Power Button: Turns the remote controller on or off.

  • Receiver Pairing Button: Used to pair the remote controller with the receiver.

  • Red Indicator Light: Charging status indicator.

  • Green Indicator Light: Wireless signal status indicator.

  • Built-in Antenna: Supports wireless communication.

  • USB Type-C Charging Port: Used to recharge the internal battery.

  • Lanyard Hole: Allows a safety lanyard to be attached.

Understanding these buttons will help you operate the W300 more efficiently.

2. W300 Technical Specifications

The APISQUEEN W300 uses 2.4GHz wireless communication and supports five control channels.

Parameter Specification
Model W300
Wireless Frequency 2.4GHz
Number of Channels 5
Modulation GFSK
Spread Spectrum FHSS
Response Speed PWM ≤20ms
Remote Control Range Approx. 200m in open areas
Transmitter Battery 7.4V 2S LiPo
Receiver Power Supply DC 4–9V
Receiver Sensitivity -96dBm
Transmitter Power 90mA
Remote Controller Weight 100g
Receiver Weight 30g

The actual wireless range may vary depending on the surrounding environment, antenna positioning, and potential signal interference.

Receiver Channel Configuration

The five receiver channels are assigned as follows:

  • Channel 1: Supplies 5V power to the receiver.

  • Channel 2: Motor 1 control.

  • Channel 3: Motor 2 control.

  • Channel 4: Motor 3 control.

  • Channel 5: Motor 4 control.

For a dual-thruster boat or vehicle, the primary motor control connections are Channel 2 and Channel 3.

3. How to Install the W300 Receiver

Correct receiver installation is particularly important because the W300 receiver contains a built-in gyroscope for automatic heading correction.

Follow these installation recommendations:

1. Mount the receiver horizontally.

Place the receiver flat on a horizontal surface. Do not install it vertically or at an inclined angle.

2. Align the receiver with the forward direction.

The receiver should be positioned according to the forward direction of the boat or vehicle to ensure correct heading detection.

3. Secure the receiver.

Make sure the receiver remains stable during operation. Avoid excessive vibration and movement.

4. Protect the receiver from water.

Important: Although the W300 handheld remote controller is waterproof, the receiver is NOT waterproof by default.

The receiver must be installed inside a suitable waterproof enclosure or otherwise protected against water exposure.

5. Avoid magnetic interference.

Position the receiver antenna carefully and keep the receiver away from sources of magnetic interference that may affect the built-in gyroscope.

Power supply warning:

The receiver requires DC 4–9V. Its input voltage must never exceed 10V. Always use a suitable regulated power supply.

If you select the optional BEC version, the BEC supports 0–60V input and provides 5V/1A output for receiver power.

4. How to Pair the W300 Remote Controller

The W300 remote controller is already paired with its receiver before leaving the factory.

In most cases, you can use it directly after connecting the receiver and supplying power.

If the remote controller and receiver become disconnected or need to be paired again, follow these steps:

Step 1: Power on the receiver.

After powering on, the receiver's red indicator light should flash, indicating that it is not currently connected.

Step 2: Turn on the remote controller.

Press and hold the remote controller's power button. The controller will emit one beep after powering on.

Step 3: Enter pairing mode.

Press and hold the receiver pairing button on the remote controller.

The controller will emit two beeps, and its green indicator light will flash.

Step 4: Restart the receiver.

Disconnect the receiver's power supply. Wait until its red indicator light turns off, then reconnect the power.

Step 5: Confirm successful pairing.

The remote controller will emit two beeps again, and the green indicator light will remain on.

This indicates that pairing has been completed successfully.

Understanding the Receiver Indicator

The receiver has its own red LED indicator:

  • Flashing red: No signal connection.

  • Solid red: Connected successfully.

Always check the receiver indicator when troubleshooting wireless communication problems.

5. How to Use W300 Cruise Control

The W300 includes a constant-speed cruise control function that allows the propulsion system to maintain a selected throttle setting without continuously holding the joystick.

Activating Cruise Control

  1. Push the remote controller joystick upward and hold it at the desired position.

  2. Press the joystick downward once.

  3. The remote controller will emit two beeps, indicating that cruise control mode has been activated.

Adjusting Cruise Speed

Once cruise control is active:

  • Press the Acceleration button to increase the cruise speed.

  • Press the Deceleration button to decrease the cruise speed.

This allows you to adjust the propulsion output without continuously operating the joystick.

Canceling Cruise Control

To exit cruise control mode:

  1. Move the joystick downward.

  2. The remote controller will emit one beep.

  3. Cruise control will be canceled, returning the system to normal manual operation.

Important: Cruise control maintains the selected throttle command. It does not guarantee a fixed actual boat speed under changing water conditions, current, wind, or load.

6. Automatic Heading Correction with the Built-in Gyroscope

One of the W300's key features is its automatic heading correction function.

During boat operation, wind, water currents, and uneven propulsion forces can cause the boat to deviate from its intended straight-line direction.

The W300 receiver contains a built-in gyroscope that automatically adjusts the thrust output of the two propellers to help correct the heading.

How Does Automatic Heading Correction Work?

When two compatible thrusters are installed:

  • The receiver monitors the vehicle's heading.

  • The gyroscope detects deviations from the intended direction.

  • The system automatically adjusts the thrust of the two propellers.

  • The boat is assisted in maintaining a straighter course.

This function is particularly useful for dual-thruster boats and marine vehicles.

Important limitations:

  • Automatic heading correction only works when controlling two propellers.

  • It is ineffective when using only one propeller.

  • Correct horizontal receiver installation is essential.

What If Automatic Heading Correction Does Not Work?

If the boat cannot maintain a straight course while moving forward or operating in cruise mode, the gyroscope may need recalibration.

According to the W300 manual:

  1. Bring the boat to a complete stop in open water.

  2. Make sure the boat is positioned horizontally.

  3. Press and hold the left-side button to calibrate the gyroscope.

Perform calibration under stable conditions and avoid moving the boat during the process.

7. Optional GPS Electronic Anchor Function

The W300 also supports an optional GPS electronic anchor function.

This feature is designed for situations where a boat needs to remain in a relatively fixed position in a river or waterway.

Wind and water currents may cause a boat to drift even when the propulsion system is not actively moving it forward.

The electronic anchor function helps compensate for this movement.

How to Activate Electronic Anchor Mode

  1. Position the boat facing against the wind or water current.

  2. Briefly press the OK button to activate the electronic anchor function.

  3. The system will begin working to maintain the boat's position.

How to Cancel Electronic Anchor Mode

Briefly press the OK button again to cancel the function.

Important: The electronic anchor function is an optional feature and requires the corresponding GPS hardware. It cannot guarantee 100% precise positioning, especially under changing environmental conditions.

8. How to Calibrate the W300 Remote Controller Throttle

During operation, you may notice that a connected motor rotates automatically or moves slowly back and forth even when the joystick is in the neutral position.

In this situation, the remote controller's throttle may need calibration.

Follow the procedure below.

Step 1: Enter calibration mode.

Press and hold the joystick downward until the remote controller emits five consecutive beeps.

The controller has now entered joystick calibration mode.

Step 2: Calibrate the joystick range.

Move the joystick to its maximum positions in any order:

  • Forward

  • Backward

  • Left

  • Right

After reaching all four maximum positions, release the joystick.

Step 3: Save the calibration.

Press and hold the OK button until the remote controller emits two beeps.

This indicates that calibration has been completed successfully.

After calibration, check whether the connected motor remains stationary when the joystick returns to its neutral position.

9. Runaway Protection and Automatic Shutdown

The W300 includes a runaway protection function designed to protect the throttle channel when the receiver loses communication with the transmitter.

When the receiver no longer receives a valid signal, the throttle channel returns to its configured default or preset value.

This function helps prevent uncontrolled throttle behavior caused by signal loss.

The actual response depends on the configured fail-safe value, so users should verify the intended safe throttle setting before operating the boat.

Automatic Shutdown

The W300 also supports automatic shutdown:

  • Disconnecting power to the thruster will turn off the receiver.

  • If the remote controller cannot communicate with the receiver for 10 minutes, the remote controller will automatically shut down.

These functions help reduce unnecessary power consumption when the system is not in use.

10. How to Charge the W300 Remote Controller

The W300 remote controller has a built-in rechargeable 7.4V lithium battery.

Charging instructions:

  1. Open the waterproof charging port cover.

  2. Connect a suitable USB Type-C charging cable.

  3. Use a 5V mobile phone charger.

  4. Turn off the remote controller while charging.

  5. Disconnect the charging cable after charging is complete.

  6. Close the waterproof charging port cover securely before using the remote controller in wet conditions.

Charging Indicator

According to the user manual:

  • Red light: Charging.

  • Green light: Fully charged.

Always keep the charging port dry during charging.

11. W300 Troubleshooting: Common Problems and Solutions

Problem 1: The Remote Controller Cannot Connect to the Receiver

Check the following:

  • Confirm that the receiver is receiving power.

  • Check whether the receiver's red LED is flashing or solid.

  • Confirm that the remote controller is switched on.

  • If necessary, repeat the pairing procedure.

Problem 2: The Motor Rotates Even When the Joystick Is in Neutral

This may indicate incorrect throttle calibration.

Follow the throttle calibration procedure described in Section 8.

Problem 3: The Boat Cannot Maintain a Straight Course

Check:

  • Whether the receiver is installed horizontally.

  • Whether the receiver is aligned with the forward direction.

  • Whether two propellers are connected and configured correctly.

  • Whether the gyroscope requires recalibration.

  • Whether magnetic interference is affecting the receiver.

Remember that automatic heading correction only works with two propellers.

Problem 4: Cruise Control Cannot Be Activated

Make sure you push the joystick upward and hold it before pressing it downward once.

Wait for the two confirmation beeps. If the controller emits a different beep sequence, check the operating status and repeat the procedure carefully.

Problem 5: The Remote Controller Suddenly Loses Connection

Check the battery level, antenna position, and receiver power supply.

Also check whether obstacles or electromagnetic interference are affecting the 2.4GHz wireless signal.

12. Frequently Asked Questions About the APISQUEEN W300

Q1: Does the W300 remote controller need to be paired before use?

The W300 remote controller is paired with its receiver at the factory. Re-pairing is normally unnecessary unless the connection has been lost or the system requires a new pairing procedure.

Q2: What is the maximum control distance of the W300?

The specified control distance is approximately 200 meters in an open area. Actual range may vary depending on environmental conditions and signal interference.

Q3: Is the W300 receiver waterproof?

No. The handheld remote controller is waterproof, but the receiver is not waterproof by default. It must be protected from water during installation and operation.

Q4: Can the W300 control two underwater thrusters?

Yes. The receiver supports separate Motor 1 and Motor 2 channels, making it suitable for compatible dual-thruster configurations.

Q5: Does the W300 support automatic heading correction?

Yes. Its built-in gyroscope can automatically adjust the thrust of two propellers to help maintain a straight course. This feature does not work with a single-propeller setup.

Q6: Can the W300 maintain a fixed boat position?

The optional GPS electronic anchor function helps compensate for wind and water currents to maintain a relatively stable position. It requires the corresponding GPS hardware and does not guarantee perfectly precise positioning.

Q7: What should I do if the motor moves when the joystick is in the neutral position?

Perform throttle calibration using the five-beep calibration procedure. This helps the controller recognize the correct joystick range and neutral position.

Q8: What voltage does the W300 receiver require?

The receiver requires DC 4–9V, and its input voltage must not exceed 10V. If using the optional BEC version, check its specified 0–60V input and 5V/1A output.

Conclusion

The APISQUEEN W300 is more than a standard wireless remote controller. Its five-channel receiver, dual-motor control, cruise control, and built-in gyroscope provide useful control functions for compatible boats and marine propulsion systems.

For the best operating experience, remember these essential points:

  • Keep the receiver horizontally mounted and properly protected from water.

  • The remote controller is factory-paired, so re-pairing is usually unnecessary.

  • Use cruise control to maintain a selected throttle setting.

  • Use automatic heading correction with a dual-propeller configuration.

  • Calibrate the throttle if the motor moves unexpectedly at neutral.

  • Never exceed the receiver's specified input voltage.

With proper installation and calibration, the W300 can provide convenient wireless control for compatible boat thrusters and marine vehicle projects.

For more information, visit the APISQUEEN W300 Wireless Waterproof Remote Controller product page or contact the APISQUEEN technical support team.

Read next

Leave a comment

  • ITEM BAR TITLE

    Share shipping, delivery, policy information.

  • ITEM BAR TITLE

    Share shipping, delivery, policy information.

  • ITEM BAR TITLE

    Share shipping, delivery, policy information.

  • ITEM BAR TITLE

    Share shipping, delivery, policy information.